 鲜花( 48)  鸡蛋( 0)
|
also check this:
) }( [( Q& }! ^+ F% L( g
' d/ k' S4 T, C2 F# ?$ f8 ~; DPressing for one second arms the system by activating the; z# m* X4 O# }
starter kill and locking the doors (if the door locks are connected).+ d/ i0 I q3 C! @5 t" p% }- @
The horn will honk (if connected) and the parking lights will flash
0 u* V* x8 L# A, q& M5 B! A" tonce to confirm arming of the system. While the system is armed,
( r& U9 I2 L$ S7 }7 M Qthe status LED will flash once per second. The Failsafe® Starter Kill! F0 |7 I+ N7 [& a$ u1 g# i
(if installed) will also prevent the vehicle’s starter from cranking.$ ~- o: s+ m2 d
Arming# D/ R: z$ s$ W, X4 ] S3 H3 _: a
© 2005 Directed Electronics—all rights reserved 9
# t$ C: ]; j& p9 f2 sThe system can also be programmed to arm the optional Failsafe®
! s1 z9 v8 H4 y5 J, l$ M* S/ _- tStarter Kill automatically (called Passive Mode). If the system has
$ D9 S5 V! j! o) E2 _been programmed for Passive Mode, the Failsafe® Starter Kill will& b8 Y. s9 |5 a( U* f+ }
automatically activate 30 seconds after the ignition has been
) }9 W8 b' C, Y! iturned off. After the ignition has been turned off, the status LED* O& x- D' H' b$ \ u" w
will flash rapidly to indicate that the system is in Passive Mode.
2 z. G5 [* i- y& P* V/ zIf Passive Mode has been programmed on, then it is also possible
. `0 @; W$ b; }9 x- c/ i% _to program the system for Passive Locking. With Passive Locking,
/ N5 F# G/ r& O8 [! {the vehicle doors lock automatically at the same time that the Failsafe®5 O. G/ B8 r7 I+ ?
Starter Kill is activated. If Passive Locking is programmed on, care+ j. @. Z5 r8 |+ b0 Z+ j
must be taken to prevent the keys from being locked in the vehicle.
, j0 A2 I# v, E0 }0 p0 b% t' x) p0 f* FNOTE: For Passive Mode to be effective, the Failsafe® Starter Kill relay
8 k2 g; Q9 M0 smust be installed.
& ~7 L4 ^! r& X7 ?$ r: yPressing for one second disarms the system and unlocks the
9 m, K+ _! k# k# L" X9 g8 }& @doors (if connected). The horn will honk twice (if connected) and
( R" K; ~7 o6 S" Kthe parking lights will flash twice to confirm disarming of the system.5 P/ z/ o6 D) ^! v- U1 y4 u% k5 N
The optional Failsafe® Starter Kill will be deactivated. The status& z* u! T! K, Y
LED will turn off, unless the system is programmed for Passive1 D! ]! O; K0 u, N% a
Mode. In Passive Mode, the status LED will flash rapidly when the! C- ^& p; D8 m4 M% Y: q
system is disarmed. This indicates that the system will re-engage
( h2 O4 \- E- t' V0 [$ R; Xthe starter kill and re-lock the doors (if Passive Locking has been
8 Y9 y! G. |+ k) vprogrammed) in 30 seconds unless the ignition is turned on.
) ~$ A* g8 N2 ?Disarming
' B) V8 L+ Y: c5 A/ S: b8 e10 © 2005 Directed Electronics—all rights reserved7 c3 [" X+ t5 @( ^
If your remote transmitter is lost or damaged, you can manually. w& X$ w% T5 V, ]5 K" A/ v
override the starter kill. To do this, you must have the vehicle's' R a. l1 e) v& w
ignition key and know where the Valet button is located. Be sure- ]5 r7 d+ K' k
to check with the installer for the location of the Valet button.
8 I5 J, F1 Q( NTo override the starter kill, turn& p- x' |- V9 s
the ignition on and press the6 g: v4 a/ y5 E, ?
Valet button within 10 seconds.7 m4 S! M5 t/ ~1 @( O. l
The status LED will stop flashing
% T4 Y7 ]3 h0 W1 S2 sand the vehicle should start. If it does not start,, z& A+ y' @6 w; G* l2 l
you may have waited too long; turn the ignition off and repeat the: V- t$ P% S+ B- A+ I7 }) S
process.$ X9 z* Z' z/ }
LOCATION OF VALET BUTTON_____________________________
# D0 N/ T Y4 [You can prevent your system from automatically activating the
/ _; {, S$ K% g$ _# }Failsafe® Starter Kill and locking the doors by using Valet Mode.
" r7 B6 `+ ]3 L8 s! r1 sThis is very useful when washing the vehicle or having it serviced.( ]7 B4 Z( v' N+ d6 e+ g5 b
In Valet Mode, the starter kill cannot be activated, even with the" C) S7 ]9 x0 U& p: i4 N, n% R X; n
transmitter, but all convenience functions (door locks, remote* L' w) @9 I# p) _* i
start, etc.) will continue to work normally. |
|